Mono amplifier
OGS4500A.1D
4,500 W RMS · 1 ohm stable · Strappable
OG Audio's most powerful monoblock, for builds running several subwoofers. One gives 4,500 W RMS at 1 ohm; a strapped pair gives 9,000 W RMS at 2 ohm.
- 30-day returns · No questions asked
- Ships in 2–3 business days · Free shipping on every US order
Top-of-range monoblock for extreme multi-sub builds and strapped-pair setups.
The OGS4500A.1D sits at the top of OG Audio's Class D monoblock range, rated at 4,500W RMS at 1 ohm, 2,900W RMS at 2 ohm and 1,600W RMS at 4 ohm. For the heaviest builds, strap two units for 9,000W RMS at 2 ohm; the hardware is included. A damping factor over 200 and THD under 0.10% keep the output controlled, while 0–9 dB bass EQ, 0–180 degree phase control and a remote level control handle the tuning. Plan around its 450A fuse rating, or 900A when strapped.
See the full specs→- Flagship Output4,500W RMS at 1 ohm, 2,900W RMS at 2 ohm and 1,600W RMS at 4 ohm, all published.
- 9,000W Strapped PairTwo units strapped deliver 9,000W RMS at 2 ohm, with the connection hardware included.
- Tight Output ControlDamping factor over 200, THD under 0.10% and efficiency over 90% at 4 ohm keep the stage clean.
- Full Tuning SetA 35–250 Hz low-pass, 10–50 Hz subsonic, 0–9 dB bass EQ and 0–180 degree phase are all on board.
RMS @ 1 OHM
4,500 Watt
RMS @ 2 OHM
2,900 Watt
RMS @ 4 OHM
1,600 Watt
Power at every load
Wire your subwoofers to one of these final loads. The number above it is the RMS this amp delivers there.
The details
- Channels
- Mono
- Class
- Class D (MOSFET)
- Frequency response
- 20–250 Hz
- Efficiency
- Over 90% at 4 ohm
- THD
- Under 0.10%
- Signal-to-noise ratio
- Over 90 dB
- Damping factor
- Over 200
- Strappable
- Two units: 9,000 W RMS at 2 ohm (hardware included)
- Status light
- Top LED
- Dimensions
- 23.74 × 8.27 × 2.5″ (603 × 210 × 63.5 mm)
- RMS at 1 ohm
- 4,500 W
- RMS at 2 ohm
- 2,900 W
- RMS at 4 ohm
- 1,600 W
- Stable at
- 1 ohm
- Fuse
- 450 A (900 A strapped)
- Low-pass filter
- 35–250 Hz
- Subsonic filter
- 10–50 Hz
- Bass EQ
- 0–9 dB
- Phase
- 0–180°
- Remote level control
- Included
- Inputs
- High-level (speaker) and RCA
- Input sensitivity
- 0.2–6 V
- Fan socket
- Yes
- Power & ground cable
- 0 AWG
- Internal fuse
- None (an external fuse is required)
Goes well with
Picked by the numbers on each spec sheet: power at the load it wires to, and parts sized to fit.
-
OGWZ123500AD212″3,500 W RMSDual 2 ohmCoils in parallel make 1 ohm, where this amp delivers 4,500 W RMS, with headroom over the sub's 3,500 W rating.
$899
-
OGWZ153500AD215″3,500 W RMSDual 2 ohmCoils in parallel make 1 ohm, where this amp delivers 4,500 W RMS, with headroom over the sub's 3,500 W rating.
$999
-
OGWZ123500AD112″3,500 W RMSDual 1 ohmCoils in series make 2 ohm, where this amp delivers 2,900 W RMS, under the sub's 3,500 W rating.
$899
-
OGWZ153500AD115″3,500 W RMSDual 1 ohmCoils in series make 2 ohm, where this amp delivers 2,900 W RMS, under the sub's 3,500 W rating.
$999
Questions
Reach the OG Audio team for product questions, order support, warranty claims, and tuning help.
4,500 W RMS at 1 ohm, 2,900 W RMS at 2 ohm and 1,600 W RMS at 4 ohm. It is 1 ohm stable, so wiring to a 1 ohm final load reaches the full 4,500 W.
Two strapped units deliver 9,000 W RMS at 2 ohm, and the strapping hardware is included. The recommended fuse rating rises to 900 A when strapped.
450 A is the recommended fuse for one amplifier. Plan the dedicated power run around it, and confirm your battery and alternator can supply the current at full output.
High-level speaker and RCA inputs accept 0.2–6 V, so a factory radio or an aftermarket source connects. Tuning covers a 35–250 Hz low-pass, 10–50 Hz subsonic, 0–9 dB bass EQ and 0–180 degree phase.
Talk to us
Not sure it fits your build? Ask the OG Audio team before you order.
Contact usMore amplifiers
